ボイラー製造工
建設・メンテナンス・修理AI露出度
- データ出典: BLS公表時点: 2026-08
低い· 相対
低い4段階の相対区分非常に高い職業群単位の値
尺度・母数・出典
4段階の相対区分（低い / 中程度 / 高い / 非常に高い）
BLS雇用見通し表の詳細職業831件が母数。値は NEM(全国雇用マトリクス)コード単位で付与されるため、同じ NEM コードの職業は同じバンドになります
- データ出典: Anthropic公表時点: 2026-03
0.000
0.000ここに掲載された値の範囲0.745尺度・母数・出典
- データ出典: ILO公表時点: 2025
0.21
0.09ここに掲載された値の範囲0.70職業群単位の値
尺度・母数・出典
生成AI露出度指数、公開されたまま0–1
ISCO-08の職業小分類単位 — 同じコードの職業はすべて同じ値
当サイトの算出であり、ILOが公表した数値ではありません。当サイトがILOデータセットに結び付けた職業1,012件のうち、この値以上のものは82%です。
この出典がどのような性格の値か
BLSの区分は絶対水準ではなく相対順位であり、一次測定でもありません。複数の既存研究が付けた職業別パーセンタイル順位を4段階にまとめた値です。雇用や賃金の予測でもなく、導入確率でもなく、自動化と増強を区別しません。
Task-level exposure
露出のある作業のみValues in this tab are predicted labels, not observations. Eloundou et al. (2023) published two rating regimes — human raters and GPT-4 — and the β shown here is derived from the GPT-4 rater basis alone; the same task can take a different value under the other regime. The unit and the meaning differ from the observed shares (%) in the other tabs, so do not place them on the same axis.
| Task | βE1 + 0.5 × E2 |
|---|---|
Study blueprints to determine locations, relationships, or dimensions of parts.O*NET Task ID 11446 | 0.5 |
Examine boilers, pressure vessels, tanks, or vats to locate defects, such as leaks, weak spots, or defective sections, so that they can be repaired.O*NET Task ID 11438 | 0.0 |
Bolt or arc weld pressure vessel structures and parts together, using wrenches or welding equipment.O*NET Task ID 11439 | 0.0 |
Inspect assembled vessels or individual components, such as tubes, fittings, valves, controls, or auxiliary mechanisms, to locate any defects.O*NET Task ID 11440 | 0.0 |
Repair or replace defective pressure vessel parts, such as safety valves or regulators, using torches, jacks, caulking hammers, power saws, threading dies, welding equipment, or metalworking machinery.O*NET Task ID 11441 | 0.0 |
Attach rigging and signal crane or hoist operators to lift heavy frame and plate sections or other parts into place.O*NET Task ID 11442 | 0.0 |
Bell, bead with power hammers, or weld pressure vessel tube ends to ensure leakproof joints.O*NET Task ID 11443 | 0.0 |
Lay out plate, sheet steel, or other heavy metal and locate and mark bending and cutting lines, using protractors, compasses, and drawing instruments or templates.O*NET Task ID 11444 | 0.0 |
Install manholes, handholes, taps, tubes, valves, gauges, or feedwater connections in drums of water tube boilers, using hand tools.O*NET Task ID 11445 | 0.0 |
Straighten or reshape bent pressure vessel plates or structure parts, using hammers, jacks, or torches.O*NET Task ID 11447 | 0.0 |
Shape seams, joints, or irregular edges of pressure vessel sections or structural parts to attain specified fit of parts, using cutting torches, hammers, files, or metalworking machines.O*NET Task ID 11448 | 0.0 |
Position, align, and secure structural parts or related assemblies to boiler frames, tanks, or vats of pressure vessels, following blueprints.O*NET Task ID 11449 | 0.0 |
Locate and mark reference points for columns or plates on boiler foundations, following blueprints and using straightedges, squares, transits, or measuring instruments.O*NET Task ID 11450 | 0.0 |
Shape or fabricate parts, such as stacks, uptakes, or chutes, to adapt pressure vessels, heat exchangers, or piping to premises, using heavy-metalworking machines such as brakes, rolls, or drill presses.O*NET Task ID 11451 | 0.0 |
Clean pressure vessel equipment, using scrapers, wire brushes, and cleaning solvents.O*NET Task ID 11452 | 0.0 |
Install refractory bricks or other heat-resistant materials in fireboxes of pressure vessels.O*NET Task ID 11453 | 0.0 |
Assemble large vessels in an on-site fabrication shop prior to installation to ensure proper fit.O*NET Task ID 11454 | 0.0 |
β = E1 + 0.5 × E2 · E1 = tasks where direct LLM access alone cuts time by at least 50%, E2 = tasks where software built on top of an LLM cuts time by at least 50%. Values take only 0 / 0.5 / 1.0.
Data sources & licenses — O*NET®, Eloundou et al. (2023): see full notices on the Credits page