乾式壁・天井タイル設置工
建設・メンテナンス・修理AI露出度
- データ出典: BLS公表時点: 2026-08
低い· 相対
低い4段階の相対区分非常に高い職業群単位の値
尺度・母数・出典
4段階の相対区分（低い / 中程度 / 高い / 非常に高い）
BLS雇用見通し表の詳細職業831件が母数。値は NEM(全国雇用マトリクス)コード単位で付与されるため、同じ NEM コードの職業は同じバンドになります
- データ出典: Anthropic公表時点: 2026-03
0.000
0.000ここに掲載された値の範囲0.745尺度・母数・出典
- データ出典: ILO公表時点: 2025
0.11
0.09ここに掲載された値の範囲0.70職業群単位の値
尺度・母数・出典
生成AI露出度指数、公開されたまま0–1
ISCO-08の職業小分類単位 — 同じコードの職業はすべて同じ値
当サイトの算出であり、ILOが公表した数値ではありません。当サイトがILOデータセットに結び付けた職業1,012件のうち、この値以上のものは98%です。
この出典がどのような性格の値か
BLSの区分は絶対水準ではなく相対順位であり、一次測定でもありません。複数の既存研究が付けた職業別パーセンタイル順位を4段階にまとめた値です。雇用や賃金の予測でもなく、導入確率でもなく、自動化と増強を区別しません。
Task-level exposure
露出のある作業のみValues in this tab are predicted labels, not observations. Eloundou et al. (2023) published two rating regimes — human raters and GPT-4 — and the β shown here is derived from the GPT-4 rater basis alone; the same task can take a different value under the other regime. The unit and the meaning differ from the observed shares (%) in the other tabs, so do not place them on the same axis.
| Task | βE1 + 0.5 × E2 |
|---|---|
Measure and mark surfaces to lay out work, according to blueprints or drawings, using tape measures, straightedges or squares, and marking devices.O*NET Task ID 13503 | 0.5 |
Read blueprints or other specifications to determine methods of installation, work procedures, or material or tool requirements.O*NET Task ID 13504 | 0.5 |
Fit and fasten wallboard or drywall into position on wood or metal frameworks, using glue, nails, or screws.O*NET Task ID 13505 | 0.0 |
Hang dry lines to wall moldings to guide positioning of main runners.O*NET Task ID 13506 | 0.0 |
Measure and cut openings in panels or tiles for electrical outlets, windows, vents, plumbing, or other fixtures, using keyhole saws or other cutting tools.O*NET Task ID 13507 | 0.0 |
Hang drywall panels on metal frameworks of walls and ceilings in offices, schools, or other large buildings, using lifts or hoists to adjust panel heights, when necessary.O*NET Task ID 13508 | 0.0 |
Assemble or install metal framing or decorative trim for windows, doorways, or vents.O*NET Task ID 13509 | 0.0 |
Coordinate work with drywall finishers who cover the seams between drywall panels.O*NET Task ID 13510 | 0.0 |
Trim rough edges from wallboard to maintain even joints, using knives.O*NET Task ID 13511 | 0.0 |
Cut and screw together metal channels to make floor or ceiling frames, according to plans for the location of rooms or hallways.O*NET Task ID 13512 | 0.0 |
Inspect furrings, mechanical mountings, or masonry surfaces for plumbness and level, using spirit or water levels.O*NET Task ID 13513 | 0.0 |
Cut fixture or border tiles to size, using keyhole saws, and insert them into surrounding frameworks.O*NET Task ID 13514 | 0.0 |
Cut metal or wood framing and trim to size, using cutting tools.O*NET Task ID 13515 | 0.0 |
Install horizontal and vertical metal or wooden studs to frames so that wallboard can be attached to interior walls.O*NET Task ID 13516 | 0.0 |
Scribe and cut edges of tile to fit walls where wall molding is not specified.O*NET Task ID 13517 | 0.0 |
Fasten metal or rockboard lath to the structural framework of walls, ceilings, or partitions of buildings, using nails, screws, staples, or wire-ties.O*NET Task ID 13518 | 0.0 |
Suspend angle iron grids or channel irons from ceilings, using wire.O*NET Task ID 13519 | 0.0 |
Seal joints between ceiling tiles and walls.O*NET Task ID 13520 | 0.0 |
Mount tile, using adhesives, or by nailing, screwing, stapling, or wire-tying lath directly to structural frameworks.O*NET Task ID 13521 | 0.0 |
Install blanket insulation between studs and tack plastic moisture barriers over insulation.O*NET Task ID 13522 | 0.0 |
Install metal lath where plaster applications will be exposed to weather or water, or for curved or irregular surfaces.O*NET Task ID 13523 | 0.0 |
Apply cement to backs of tiles and press tiles into place, aligning them with layout marks or joints of previously laid tile.O*NET Task ID 13524 | 0.0 |
Nail channels or wood furring strips to surfaces to provide mounting for tile.O*NET Task ID 13525 | 0.0 |
Wash concrete surfaces before mounting tile to increase adhesive qualities of surfaces, using washing soda and zinc sulfate solution.O*NET Task ID 13526 | 0.0 |
Apply or mount acoustical tile or blocks, strips, or sheets of shock-absorbing materials to ceilings or walls of buildings to reduce reflection of sound or to decorate rooms.O*NET Task ID 13527 | 0.0 |
Remove existing plaster, drywall, or paneling, using crowbars and hammers.O*NET Task ID 13528 | 0.0 |
β = E1 + 0.5 × E2 · E1 = tasks where direct LLM access alone cuts time by at least 50%, E2 = tasks where software built on top of an LLM cuts time by at least 50%. Values take only 0 / 0.5 / 1.0.
Data sources & licenses — O*NET®, Eloundou et al. (2023): see full notices on the Credits page