Instaladores de Baldosas de Techo
Construcción, Mantenimiento y ReparaciónExposición a la IA
- Fuente de datos: BLSPublicado: 2026-08
Bajo· relativa
BajoCuatro bandas relativasMuy altoValor por grupo ocupacional
Escala, base y fuente
Cuatro bandas relativas (Bajo / Moderado / Alto / Muy alto)
831 ocupaciones detalladas de la tabla de proyecciones de empleo de BLS. El valor se asigna por código de la National Employment Matrix (NEM), de modo que las ocupaciones que comparten un código NEM reciben la misma banda
- Fuente de datos: AnthropicPublicado: 2026-03
0.000
0.000Rango de los valores aquí recogidos0.745Escala, base y fuente
Índice de exposición observada, 0–1 tal como se publica
Mapeado sobre tareas de O*NET
- Fuente de datos: ILOPublicado: 2025
0.11
0.09Rango de los valores aquí recogidos0.70Valor por grupo ocupacional
Escala, base y fuente
Índice de exposición a la IA generativa, 0–1 tal como se publica
Grupo primario de la CIUO-08 — todas las ocupaciones con ese código reciben este valor
Calculado por este sitio, no publicado por la OIT: de las 1012 ocupaciones que este sitio vincula al conjunto de datos de la OIT, un 98% alcanza o supera este valor.
Qué tipo de cifra publica esta fuente
La categoría de BLS es un rango relativo, no un nivel absoluto, y tampoco es una medición de primera mano: agrupa en cuatro bandas los rangos percentiles de la ocupación en varios estudios publicados. No es una previsión de empleo ni de salarios, no es una probabilidad de adopción y no distingue entre automatización y aumento.
Task-level exposure
Solo tareas expuestasValues in this tab are predicted labels, not observations. Eloundou et al. (2023) published two rating regimes — human raters and GPT-4 — and the β shown here is derived from the GPT-4 rater basis alone; the same task can take a different value under the other regime. The unit and the meaning differ from the observed shares (%) in the other tabs, so do not place them on the same axis.
| Task | βE1 + 0.5 × E2 |
|---|---|
Measure and mark surfaces to lay out work, according to blueprints or drawings, using tape measures, straightedges or squares, and marking devices.O*NET Task ID 13503 | 0.5 |
Read blueprints or other specifications to determine methods of installation, work procedures, or material or tool requirements.O*NET Task ID 13504 | 0.5 |
Fit and fasten wallboard or drywall into position on wood or metal frameworks, using glue, nails, or screws.O*NET Task ID 13505 | 0.0 |
Hang dry lines to wall moldings to guide positioning of main runners.O*NET Task ID 13506 | 0.0 |
Measure and cut openings in panels or tiles for electrical outlets, windows, vents, plumbing, or other fixtures, using keyhole saws or other cutting tools.O*NET Task ID 13507 | 0.0 |
Hang drywall panels on metal frameworks of walls and ceilings in offices, schools, or other large buildings, using lifts or hoists to adjust panel heights, when necessary.O*NET Task ID 13508 | 0.0 |
Assemble or install metal framing or decorative trim for windows, doorways, or vents.O*NET Task ID 13509 | 0.0 |
Coordinate work with drywall finishers who cover the seams between drywall panels.O*NET Task ID 13510 | 0.0 |
Trim rough edges from wallboard to maintain even joints, using knives.O*NET Task ID 13511 | 0.0 |
Cut and screw together metal channels to make floor or ceiling frames, according to plans for the location of rooms or hallways.O*NET Task ID 13512 | 0.0 |
Inspect furrings, mechanical mountings, or masonry surfaces for plumbness and level, using spirit or water levels.O*NET Task ID 13513 | 0.0 |
Cut fixture or border tiles to size, using keyhole saws, and insert them into surrounding frameworks.O*NET Task ID 13514 | 0.0 |
Cut metal or wood framing and trim to size, using cutting tools.O*NET Task ID 13515 | 0.0 |
Install horizontal and vertical metal or wooden studs to frames so that wallboard can be attached to interior walls.O*NET Task ID 13516 | 0.0 |
Scribe and cut edges of tile to fit walls where wall molding is not specified.O*NET Task ID 13517 | 0.0 |
Fasten metal or rockboard lath to the structural framework of walls, ceilings, or partitions of buildings, using nails, screws, staples, or wire-ties.O*NET Task ID 13518 | 0.0 |
Suspend angle iron grids or channel irons from ceilings, using wire.O*NET Task ID 13519 | 0.0 |
Seal joints between ceiling tiles and walls.O*NET Task ID 13520 | 0.0 |
Mount tile, using adhesives, or by nailing, screwing, stapling, or wire-tying lath directly to structural frameworks.O*NET Task ID 13521 | 0.0 |
Install blanket insulation between studs and tack plastic moisture barriers over insulation.O*NET Task ID 13522 | 0.0 |
Install metal lath where plaster applications will be exposed to weather or water, or for curved or irregular surfaces.O*NET Task ID 13523 | 0.0 |
Apply cement to backs of tiles and press tiles into place, aligning them with layout marks or joints of previously laid tile.O*NET Task ID 13524 | 0.0 |
Nail channels or wood furring strips to surfaces to provide mounting for tile.O*NET Task ID 13525 | 0.0 |
Wash concrete surfaces before mounting tile to increase adhesive qualities of surfaces, using washing soda and zinc sulfate solution.O*NET Task ID 13526 | 0.0 |
Apply or mount acoustical tile or blocks, strips, or sheets of shock-absorbing materials to ceilings or walls of buildings to reduce reflection of sound or to decorate rooms.O*NET Task ID 13527 | 0.0 |
Remove existing plaster, drywall, or paneling, using crowbars and hammers.O*NET Task ID 13528 | 0.0 |
β = E1 + 0.5 × E2 · E1 = tasks where direct LLM access alone cuts time by at least 50%, E2 = tasks where software built on top of an LLM cuts time by at least 50%. Values take only 0 / 0.5 / 1.0.
Data sources & licenses — O*NET®, Eloundou et al. (2023): see full notices on the Credits page