Instaladores y Reparadores de Lineas Electricas

Construcción, Mantenimiento y Reparación

Exposición a la IA

  • Fuente de datos: BLSPublicado: 2026-08

    Bajo· relativa

    BajoCuatro bandas relativasMuy alto

    Valor por grupo ocupacional

    Escala, base y fuente

    Cuatro bandas relativas (Bajo / Moderado / Alto / Muy alto)

    831 ocupaciones detalladas de la tabla de proyecciones de empleo de BLS. El valor se asigna por código de la National Employment Matrix (NEM), de modo que las ocupaciones que comparten un código NEM reciben la misma banda

    Conjunto de datos de origen (descarga XLSX)

  • Fuente de datos: AnthropicPublicado: 2026-03

    0.000

    0.000Rango de los valores aquí recogidos0.745
    Escala, base y fuente

    Índice de exposición observada, 0–1 tal como se publica

    Mapeado sobre tareas de O*NET

    Conjunto de datos de origen

  • Fuente de datos: ILOPublicado: 2025

    0.15

    0.09Rango de los valores aquí recogidos0.70

    Valor por grupo ocupacional

    Escala, base y fuente

    Índice de exposición a la IA generativa, 0–1 tal como se publica

    Grupo primario de la CIUO-08 — todas las ocupaciones con ese código reciben este valor

    Calculado por este sitio, no publicado por la OIT: de las 1012 ocupaciones que este sitio vincula al conjunto de datos de la OIT, un 92% alcanza o supera este valor.

    Conjunto de datos de origen

Qué tipo de cifra publica esta fuente

La categoría de BLS es un rango relativo, no un nivel absoluto, y tampoco es una medición de primera mano: agrupa en cuatro bandas los rangos percentiles de la ocupación en varios estudios publicados. No es una previsión de empleo ni de salarios, no es una probabilidad de adopción y no distingue entre automatización y aumento.

Task-level exposure

Solo tareas expuestas
TaskClaude.aiRaw / share %
Identify defective sectionalizing devices, circuit breakers, fuses, voltage regulators, transformers, switches, relays, or wiring, using wiring diagrams and electrical-testing instruments.

49-9051

0.0022100.0
Not observed on any surface — 22 task(s) — These tasks have no row in the source for this release. The 0 in the share row is a display-stage composition ratio; absence is what the — in the raw row states.
Adhere to safety practices and procedures, such as checking equipment regularly and erecting barriers around work areas.
—0
Open switches or attach grounding devices to remove electrical hazards from disturbed or fallen lines or to facilitate repairs.
—0
Climb poles or use truck-mounted buckets to access equipment.
—0
Place insulating or fireproofing materials over conductors and joints.
—0
Install, maintain, and repair electrical distribution and transmission systems, including conduits, cables, wires, and related equipment, such as transformers, circuit breakers, and switches.
—0
Drive vehicles equipped with tools and materials to job sites.
—0
Coordinate work assignment preparation and completion with other workers.
—0
Inspect and test power lines and auxiliary equipment to locate and identify problems, using reading and testing instruments.
—0
String wire conductors and cables between poles, towers, trenches, pylons, and buildings, setting lines in place and using winches to adjust tension.
—0
Test conductors, according to electrical diagrams and specifications, to identify corresponding conductors and to prevent incorrect connections.
—0
Replace or straighten damaged poles.
—0
Install watt-hour meters and connect service drops between power lines and consumers' facilities.
—0
Attach cross-arms, insulators, and auxiliary equipment to poles prior to installing them.
—0
Travel in trucks, helicopters, and airplanes to inspect lines for freedom from obstruction and adequacy of insulation.
—0
Dig holes, using augers, and set poles, using cranes and power equipment.
—0
Trim trees that could be hazardous to the functioning of cables or wires.
—0
Splice or solder cables together or to overhead transmission lines, customer service lines, or street light lines, using hand tools, epoxies, or specialized equipment.
—0
Clean, tin, and splice corresponding conductors by twisting ends together or by joining ends with metal clamps and soldering connections.
—0
Pull up cable by hand from large reels mounted on trucks.
—0
Lay underground cable directly in trenches, or string it through conduit running through the trenches.
—0
Cut and peel lead sheathing and insulation from defective or newly installed cables and conduits prior to splicing.
—0
Cut trenches for laying underground cables, using trenchers and cable plows.
—0

Data sources & licenses — O*NET®, Anthropic Economic Index, Eloundou et al. (2023): see full notices on the Credits page

Información ocupacional