Techadores

Construcción, Mantenimiento y Reparación

Exposición a la IA

  • Fuente de datos: BLSPublicado: 2026-08

    Bajo· relativa

    BajoCuatro bandas relativasMuy alto

    Valor por grupo ocupacional

    Escala, base y fuente

    Cuatro bandas relativas (Bajo / Moderado / Alto / Muy alto)

    831 ocupaciones detalladas de la tabla de proyecciones de empleo de BLS. El valor se asigna por código de la National Employment Matrix (NEM), de modo que las ocupaciones que comparten un código NEM reciben la misma banda

    Conjunto de datos de origen (descarga XLSX)

  • Fuente de datos: AnthropicPublicado: 2026-03

    0.016

    0.000Rango de los valores aquí recogidos0.745
    Escala, base y fuente

    Índice de exposición observada, 0–1 tal como se publica

    Mapeado sobre tareas de O*NET

    Conjunto de datos de origen

  • Fuente de datos: ILOPublicado: 2025

    0.13

    0.09Rango de los valores aquí recogidos0.70

    Valor por grupo ocupacional

    Escala, base y fuente

    Índice de exposición a la IA generativa, 0–1 tal como se publica

    Grupo primario de la CIUO-08 — todas las ocupaciones con ese código reciben este valor

    Calculado por este sitio, no publicado por la OIT: de las 1012 ocupaciones que este sitio vincula al conjunto de datos de la OIT, un 97% alcanza o supera este valor.

    Conjunto de datos de origen

Qué tipo de cifra publica esta fuente

La categoría de BLS es un rango relativo, no un nivel absoluto, y tampoco es una medición de primera mano: agrupa en cuatro bandas los rangos percentiles de la ocupación en varios estudios publicados. No es una previsión de empleo ni de salarios, no es una probabilidad de adopción y no distingue entre automatización y aumento.

Task-level exposure

Solo tareas expuestas
TaskClaude.aiRaw / share %APIRaw / share %
Estimate materials and labor required to complete roofing jobs.

47-2181

0.0036100.00.0055100.0
Not observed on any surface — 27 task(s) — These tasks have no row in the source for this release. The 0 in the share row is a display-stage composition ratio; absence is what the — in the raw row states.
Inspect problem roofs to determine the best repair procedures.
—0—0
Set up scaffolding to provide safe access to roofs.
—0—0
Cement or nail flashing strips of metal or shingle over joints to make them watertight.
—0—0
Install, repair, or replace single-ply roofing systems, using waterproof sheet materials such as modified plastics, elastomeric, or other asphaltic compositions.
—0—0
Cut felt, shingles, or strips of flashing to fit angles formed by walls, vents, or intersecting roof surfaces.
—0—0
Install vapor barriers or layers of insulation on flat roofs.
—0—0
Cover exposed nailheads with roofing cement or caulking to prevent water leakage or rust.
—0—0
Install partially overlapping layers of material over roof insulation surfaces, using chalk lines, gauges on shingling hatchets, or lines on shingles.
—0—0
Cover roofs or exterior walls of structures with slate, asphalt, aluminum, wood, gravel, gypsum, or related materials, using brushes, knives, punches, hammers, or other tools.
—0—0
Remove snow, water, or debris from roofs prior to applying roofing materials.
—0—0
Apply alternate layers of hot asphalt or tar and roofing paper to roofs.
—0—0
Waterproof or damp-proof walls, floors, roofs, foundations, or basements by painting or spraying surfaces with waterproof coatings or by attaching waterproofing membranes to surfaces.
—0—0
Mop or pour hot asphalt or tar onto roof bases.
—0—0
Apply plastic coatings, membranes, fiberglass, or felt over sloped roofs before applying shingles.
—0—0
Smooth rough spots to prepare surfaces for waterproofing, using hammers, chisels, or rubbing bricks.
—0—0
Glaze top layers to make a smooth finish or embed gravel in the bitumen for rough surfaces.
—0—0
Apply gravel or pebbles over top layers of roofs, using rakes or stiff-bristled brooms.
—0—0
Apply reflective roof coatings, such as special paints or single-ply roofing sheets, to existing roofs to reduce solar heat absorption.
—0—0
Install attic ventilation systems, such as turbine vents, gable or ridge vents, or conventional or solar-powered exhaust fans.
—0—0
Install skylights on roofs to increase natural light inside structures or to reduce energy costs.
—0—0
Attach roofing paper to roofs in overlapping strips to form bases for other materials.
—0—0
Spray roofs, sidings, or walls to bind, seal, insulate, or soundproof sections of structures, using spray guns, air compressors, or heaters.
—0—0
Punch holes in slate, tile, terra cotta, or wooden shingles, using punches and hammers.
—0—0
Apply modular soil- and plant-containing grids over existing roof membranes to create green roofs.
—0—0
Attach solar panels to existing roofs, according to specifications and without damaging roofing materials or the structural integrity of buildings.
—0—0
Install layers of vegetation-based green roofs, including protective membranes, drainage, aeration, water retention and filter layers, soil substrates, irrigation materials, and plants.
—0—0
Install solar roofing systems that have energy-collecting photovoltaic panels built into roofing membranes, shingles, or tiles.
—0—0

Data sources & licenses — O*NET®, Anthropic Economic Index, Eloundou et al. (2023): see full notices on the Credits page

Información ocupacional