Encintadores
Construcción, Mantenimiento y ReparaciónExposición a la IA
- Fuente de datos: BLSPublicado: 2026-08
Bajo· relativa
BajoCuatro bandas relativasMuy altoValor por grupo ocupacional
Escala, base y fuente
Cuatro bandas relativas (Bajo / Moderado / Alto / Muy alto)
831 ocupaciones detalladas de la tabla de proyecciones de empleo de BLS. El valor se asigna por código de la National Employment Matrix (NEM), de modo que las ocupaciones que comparten un código NEM reciben la misma banda
- Fuente de datos: AnthropicPublicado: 2026-03
0.000
0.000Rango de los valores aquí recogidos0.745Escala, base y fuente
Índice de exposición observada, 0–1 tal como se publica
Mapeado sobre tareas de O*NET
- Fuente de datos: ILOPublicado: 2025
0.11
0.09Rango de los valores aquí recogidos0.70Valor por grupo ocupacional
Escala, base y fuente
Índice de exposición a la IA generativa, 0–1 tal como se publica
Grupo primario de la CIUO-08 — todas las ocupaciones con ese código reciben este valor
Calculado por este sitio, no publicado por la OIT: de las 1012 ocupaciones que este sitio vincula al conjunto de datos de la OIT, un 98% alcanza o supera este valor.
Qué tipo de cifra publica esta fuente
La categoría de BLS es un rango relativo, no un nivel absoluto, y tampoco es una medición de primera mano: agrupa en cuatro bandas los rangos percentiles de la ocupación en varios estudios publicados. No es una previsión de empleo ni de salarios, no es una probabilidad de adopción y no distingue entre automatización y aumento.
Task-level exposure
Solo tareas expuestas| Task | Claude.aiRaw / share % |
|---|---|
Check adhesives to ensure that they will work and will remain durable.47-2082 | 0.0035100.0 |
| Not observed on any surface — 15 task(s) — These tasks have no row in the source for this release. The 0 in the share row is a display-stage composition ratio; absence is what the — in the raw row states. | |
Remove extra compound after surfaces have been covered sufficiently. | —0 |
Spread sealing compound between boards or panels or over cracks, holes, nail heads, or screw heads, using trowels, broadknives, or spatulas. | —0 |
Press paper tape over joints to embed tape into sealing compound and to seal joints. | —0 |
Mix sealing compounds by hand or with portable electric mixers. | —0 |
Spread and smooth cementing material over tape, using trowels or floating machines to blend joints with wall surfaces. | —0 |
Seal joints between plasterboard or other wallboard to prepare wall surfaces for painting or papering. | —0 |
Sand or patch nicks or cracks in plasterboard or wallboard. | —0 |
Use mechanical applicators that spread compounds and embed tape in one operation. | —0 |
Apply additional coats to fill in holes and make surfaces smooth. | —0 |
Install metal molding at wall corners to secure wallboard. | —0 |
Sand rough spots of dried cement between applications of compounds. | —0 |
Countersink nails or screws below surfaces of walls before applying sealing compounds, using hammers or screwdrivers. | —0 |
Select the correct sealing compound or tape. | —0 |
Apply texturizing compounds or primers to walls or ceilings before final finishing, using trowels, brushes, rollers, or spray guns. | —0 |
Work on high ceilings using scaffolding or other tools, such as stilts. | —0 |
Values in this tab are predicted labels, not observations. Eloundou et al. (2023) published two rating regimes — human raters and GPT-4 — and the β shown here is derived from the GPT-4 rater basis alone; the same task can take a different value under the other regime. The unit and the meaning differ from the observed shares (%) in the other tabs, so do not place them on the same axis.
| Task | βE1 + 0.5 × E2 |
|---|---|
Remove extra compound after surfaces have been covered sufficiently.O*NET Task ID 13529 | 0.0 |
Spread sealing compound between boards or panels or over cracks, holes, nail heads, or screw heads, using trowels, broadknives, or spatulas.O*NET Task ID 13530 | 0.0 |
Press paper tape over joints to embed tape into sealing compound and to seal joints.O*NET Task ID 13531 | 0.0 |
Mix sealing compounds by hand or with portable electric mixers.O*NET Task ID 13532 | 0.0 |
Spread and smooth cementing material over tape, using trowels or floating machines to blend joints with wall surfaces.O*NET Task ID 13533 | 0.0 |
Seal joints between plasterboard or other wallboard to prepare wall surfaces for painting or papering.O*NET Task ID 13534 | 0.0 |
Sand or patch nicks or cracks in plasterboard or wallboard.O*NET Task ID 13535 | 0.0 |
Use mechanical applicators that spread compounds and embed tape in one operation.O*NET Task ID 13536 | 0.0 |
Apply additional coats to fill in holes and make surfaces smooth.O*NET Task ID 13537 | 0.0 |
Install metal molding at wall corners to secure wallboard.O*NET Task ID 13538 | 0.0 |
Sand rough spots of dried cement between applications of compounds.O*NET Task ID 13539 | 0.0 |
Countersink nails or screws below surfaces of walls before applying sealing compounds, using hammers or screwdrivers.O*NET Task ID 13540 | 0.0 |
Select the correct sealing compound or tape.O*NET Task ID 13541 | 0.0 |
Apply texturizing compounds or primers to walls or ceilings before final finishing, using trowels, brushes, rollers, or spray guns.O*NET Task ID 13542 | 0.0 |
Check adhesives to ensure that they will work and will remain durable.O*NET Task ID 13543 | 0.0 |
Work on high ceilings, using scaffolding or other tools, such as stilts.O*NET Task ID 20788 | 0.0 |
β = E1 + 0.5 × E2 · E1 = tasks where direct LLM access alone cuts time by at least 50%, E2 = tasks where software built on top of an LLM cuts time by at least 50%. Values take only 0 / 0.5 / 1.0.
Data sources & licenses — O*NET®, Anthropic Economic Index, Eloundou et al. (2023): see full notices on the Credits page