Poseurs de Moquette
Construction, Maintenance et RéparationExposition à l'IA
- Source des données: BLSPublié: 2026-08
Faible· relative
FaibleQuatre bandes relativesTrès élevéeValeur par groupe professionnel
Échelle, base et source
Quatre bandes relatives (Faible / Modérée / Élevée / Très élevée)
831 métiers détaillés du tableau des projections d'emploi du BLS. La valeur est attribuée par code de la National Employment Matrix (NEM), si bien que les métiers partageant un code NEM reçoivent la même bande
- Source des données: AnthropicPublié: 2026-03
0.000
0.000Étendue des valeurs présentées ici0.745Échelle, base et source
- Source des données: ILOPublié: 2025
0.10
0.09Étendue des valeurs présentées ici0.70Valeur par groupe professionnel
Échelle, base et source
Indice d'exposition à l'IA générative, 0–1 tel que publié
Groupe de base CITP-08 — tous les métiers partageant le code reçoivent cette valeur
Calculé par ce site, non publié par l'OIT : sur les 1 012 professions que ce site relie au jeu de données de l'OIT, 98% atteignent ou dépassent cette valeur.
Quelle est la nature de la valeur publiée par cette source
La catégorie BLS est un rang relatif et non un niveau absolu, et ce n'est pas une mesure de première main : elle regroupe en quatre bandes les rangs centiles du métier dans plusieurs études publiées. Ce n'est ni une prévision d'emploi ou de salaire, ni une probabilité d'adoption, et elle ne distingue pas automatisation et augmentation.
Task-level exposure
| Task | Claude.aiRaw / share % |
|---|---|
Draw building diagrams and record dimensions.47-2041 | 0.00000.0 |
| Not observed on any surface — 15 task(s) — These tasks have no row in the source for this release. The 0 in the share row is a display-stage composition ratio; absence is what the — in the raw row states. | |
Join edges of carpet and seam edges where necessary, by sewing or by using tape with glue and heated carpet iron. | —0 |
Cut and trim carpet to fit along wall edges, openings, and projections, finishing the edges with a wall trimmer. | —0 |
Inspect the surface to be covered to determine its condition, and correct any imperfections that might show through carpet or cause carpet to wear unevenly. | —0 |
Roll out, measure, mark, and cut carpeting to size with a carpet knife, following floor sketches and allowing extra carpet for final fitting. | —0 |
Plan the layout of the carpet, allowing for expected traffic patterns and placing seams for best appearance and longest wear. | —0 |
Stretch carpet to align with walls and ensure a smooth surface, and press carpet in place over tack strips or use staples, tape, tacks or glue to hold carpet in place. | —0 |
Take measurements and study floor sketches to calculate the area to be carpeted and the amount of material needed. | —0 |
Cut carpet padding to size and install padding, following prescribed method. | —0 |
Install carpet on some floors using adhesive, following prescribed method. | —0 |
Nail tack strips around area to be carpeted or use old strips to attach edges of new carpet. | —0 |
Fasten metal treads across door openings or where carpet meets flooring to hold carpet in place. | —0 |
Measure, cut and install tackless strips along the baseboard or wall. | —0 |
Move furniture from area to be carpeted and remove old carpet and padding. | —0 |
Cut and bind material. | —0 |
Clean up before and after installation, including vacuuming carpet and discarding remnant pieces. | —0 |
Values in this tab are predicted labels, not observations. Eloundou et al. (2023) published two rating regimes — human raters and GPT-4 — and the β shown here is derived from the GPT-4 rater basis alone; the same task can take a different value under the other regime. The unit and the meaning differ from the observed shares (%) in the other tabs, so do not place them on the same axis.
| Task | βE1 + 0.5 × E2 |
|---|---|
Take measurements and study floor sketches to calculate the area to be carpeted and the amount of material needed.O*NET Task ID 2839 | 0.5 |
Draw building diagrams and record dimensions.O*NET Task ID 2845 | 0.5 |
Join edges of carpet and seam edges where necessary, by sewing or by using tape with glue and heated carpet iron.O*NET Task ID 2833 | 0.0 |
Cut and trim carpet to fit along wall edges, openings, and projections, finishing the edges with a wall trimmer.O*NET Task ID 2834 | 0.0 |
Inspect the surface to be covered to determine its condition, and correct any imperfections that might show through carpet or cause carpet to wear unevenly.O*NET Task ID 2835 | 0.0 |
Roll out, measure, mark, and cut carpeting to size with a carpet knife, following floor sketches and allowing extra carpet for final fitting.O*NET Task ID 2836 | 0.0 |
Plan the layout of the carpet, allowing for expected traffic patterns and placing seams for best appearance and longest wear.O*NET Task ID 2837 | 0.0 |
Stretch carpet to align with walls and ensure a smooth surface, and press carpet in place over tack strips or use staples, tape, tacks or glue to hold carpet in place.O*NET Task ID 2838 | 0.0 |
Cut carpet padding to size and install padding, following prescribed method.O*NET Task ID 2840 | 0.0 |
Install carpet on some floors using adhesive, following prescribed method.O*NET Task ID 2841 | 0.0 |
Nail tack strips around area to be carpeted or use old strips to attach edges of new carpet.O*NET Task ID 2842 | 0.0 |
Fasten metal treads across door openings or where carpet meets flooring to hold carpet in place.O*NET Task ID 2843 | 0.0 |
Measure, cut and install tackless strips along the baseboard or wall.O*NET Task ID 2844 | 0.0 |
Move furniture from area to be carpeted and remove old carpet and padding.O*NET Task ID 2846 | 0.0 |
Cut and bind material.O*NET Task ID 2847 | 0.0 |
Clean up before and after installation, including vacuuming carpet and discarding remnant pieces.O*NET Task ID 20142 | 0.0 |
β = E1 + 0.5 × E2 · E1 = tasks where direct LLM access alone cuts time by at least 50%, E2 = tasks where software built on top of an LLM cuts time by at least 50%. Values take only 0 / 0.5 / 1.0.
Data sources & licenses — O*NET®, Anthropic Economic Index, Eloundou et al. (2023): see full notices on the Credits page