दुर्दम्य सामग्री मरम्मतकर्ता
निर्माण, रखरखाव और मरम्मतAI एक्सपोजर
- डेटा स्रोत: BLSप्रकाशन: 2026-08
कम· सापेक्ष
कमचार सापेक्ष श्रेणियाँबहुत उच्चव्यवसाय-समूह स्तर का मान
मापक्रम, आधार और स्रोत
चार सापेक्ष बैंड (कम / मध्यम / उच्च / बहुत उच्च)
BLS रोज़गार पूर्वानुमान तालिका के 831 विस्तृत व्यवसायों के आधार पर। मान NEM (नेशनल एम्प्लॉयमेंट मैट्रिक्स) कोड के स्तर पर दिया जाता है, इसलिए एक ही NEM कोड वाले व्यवसायों को वही बैंड मिलता है
- डेटा स्रोत: Anthropicप्रकाशन: 2026-03
0.000
0.000यहाँ दिए गए मानों की सीमा0.745मापक्रम, आधार और स्रोत
- डेटा स्रोत: ILOप्रकाशन: 2025
0.09
0.09यहाँ दिए गए मानों की सीमा0.70व्यवसाय-समूह स्तर का मान
मापक्रम, आधार और स्रोत
जेनरेटिव AI एक्सपोजर सूचकांक, प्रकाशित रूप में 0–1
ISCO-08 यूनिट समूह — समान कोड वाले सभी व्यवसायों को यही मान मिलता है
यह इस साइट की गणना है, ILO द्वारा प्रकाशित आँकड़ा नहीं: इस साइट द्वारा ILO डेटासेट से जोड़े गए 1,012 व्यवसायों में से 100% इस मान के बराबर या उससे अधिक हैं।
यह स्रोत किस प्रकार का आँकड़ा प्रकाशित करता है
BLS की श्रेणी सापेक्ष रैंक है, निरपेक्ष स्तर नहीं, और यह प्रथम-हस्त माप भी नहीं है: यह कई प्रकाशित अध्ययनों में व्यवसाय की पर्सेंटाइल रैंकों को चार बैंडों में बांटती है। यह रोज़गार या वेतन का पूर्वानुमान नहीं है, न अपनाए जाने की संभावना, और यह स्वचालन और संवर्धन में अंतर नहीं करती।
Task-level exposure
Values in this tab are predicted labels, not observations. Eloundou et al. (2023) published two rating regimes — human raters and GPT-4 — and the β shown here is derived from the GPT-4 rater basis alone; the same task can take a different value under the other regime.
| Task | βE1 + 0.5 × E2 |
|---|---|
Reline or repair ladles and pouring spouts with refractory clay, using trowels.O*NET Task ID 13819 | 0.0 |
Chip slag from linings of ladles or remove linings when beyond repair, using hammers and chisels.O*NET Task ID 13820 | 0.0 |
Mix specified amounts of sand, clay, mortar powder, and water to form refractory clay or mortar, using shovels or mixing machines.O*NET Task ID 13821 | 0.0 |
Measure furnace walls to determine dimensions and cut required number of sheets from plastic block, using saws.O*NET Task ID 13822 | 0.0 |
Tighten locknuts holding refractory stopper assemblies together, spread mortar on jackets to seal sleeve joints, and dry mortar in ovens.O*NET Task ID 13823 | 0.0 |
Dry and bake new linings by placing inverted linings over burners, building fires in ladles, or by using blowtorches.O*NET Task ID 13824 | 0.0 |
Remove worn or damaged plastic block refractory linings of furnaces, using hand tools.O*NET Task ID 13825 | 0.0 |
Fasten stopper heads to rods with metal pins to assemble refractory stoppers used to plug pouring nozzles of steel ladles.O*NET Task ID 13826 | 0.0 |
Climb scaffolding, carrying hoses, and spray surfaces of cupolas with refractory mixtures, using spray equipment.O*NET Task ID 13827 | 0.0 |
Drill holes in furnace walls, bolt overlapping layers of plastic to walls, and hammer surfaces to compress layers into solid sheets.O*NET Task ID 13828 | 0.0 |
Spread mortar on stopper heads and rods, using trowels, and slide brick sleeves over rods to form refractory jackets.O*NET Task ID 13829 | 0.0 |
Dump and tamp clay in molds, using tamping tools.O*NET Task ID 13830 | 0.0 |
Disassemble molds, and cut, chip, and smooth clay structures such as floaters, drawbars, and L-blocks.O*NET Task ID 13831 | 0.0 |
Transfer clay structures to curing ovens, melting tanks, and drawing kilns, using forklifts.O*NET Task ID 13832 | 0.0 |
Install preformed metal scaffolding in interiors of cupolas, using hand tools.O*NET Task ID 13833 | 0.0 |
Install clay structures in melting tanks and drawing kilns to control the flow and temperature of molten glass, using hoists and hand tools.O*NET Task ID 13834 | 0.0 |
β = E1 + 0.5 × E2 · E1 = tasks where direct LLM access alone cuts time by at least 50%, E2 = tasks where software built on top of an LLM cuts time by at least 50%. Values take only 0 / 0.5 / 1.0.
Data sources & licenses — O*NET®, Eloundou et al. (2023): see full notices on the Credits page