カーペット設置工
建設・メンテナンス・修理AI露出度
- データ出典: BLS公表時点: 2026-08
低い· 相対
低い4段階の相対区分非常に高い職業群単位の値
尺度・母数・出典
4段階の相対区分（低い / 中程度 / 高い / 非常に高い）
BLS雇用見通し表の詳細職業831件が母数。値は NEM(全国雇用マトリクス)コード単位で付与されるため、同じ NEM コードの職業は同じバンドになります
- データ出典: Anthropic公表時点: 2026-03
0.000
0.000ここに掲載された値の範囲0.745尺度・母数・出典
- データ出典: ILO公表時点: 2025
0.10
0.09ここに掲載された値の範囲0.70職業群単位の値
尺度・母数・出典
生成AI露出度指数、公開されたまま0–1
ISCO-08の職業小分類単位 — 同じコードの職業はすべて同じ値
当サイトの算出であり、ILOが公表した数値ではありません。当サイトがILOデータセットに結び付けた職業1,012件のうち、この値以上のものは98%です。
この出典がどのような性格の値か
BLSの区分は絶対水準ではなく相対順位であり、一次測定でもありません。複数の既存研究が付けた職業別パーセンタイル順位を4段階にまとめた値です。雇用や賃金の予測でもなく、導入確率でもなく、自動化と増強を区別しません。
Task-level exposure
| Task | Claude.aiRaw / share % |
|---|---|
Draw building diagrams and record dimensions.47-2041 | 0.00000.0 |
| Not observed on any surface — 15 task(s) — These tasks have no row in the source for this release. The 0 in the share row is a display-stage composition ratio; absence is what the — in the raw row states. | |
Join edges of carpet and seam edges where necessary, by sewing or by using tape with glue and heated carpet iron. | —0 |
Cut and trim carpet to fit along wall edges, openings, and projections, finishing the edges with a wall trimmer. | —0 |
Inspect the surface to be covered to determine its condition, and correct any imperfections that might show through carpet or cause carpet to wear unevenly. | —0 |
Roll out, measure, mark, and cut carpeting to size with a carpet knife, following floor sketches and allowing extra carpet for final fitting. | —0 |
Plan the layout of the carpet, allowing for expected traffic patterns and placing seams for best appearance and longest wear. | —0 |
Stretch carpet to align with walls and ensure a smooth surface, and press carpet in place over tack strips or use staples, tape, tacks or glue to hold carpet in place. | —0 |
Take measurements and study floor sketches to calculate the area to be carpeted and the amount of material needed. | —0 |
Cut carpet padding to size and install padding, following prescribed method. | —0 |
Install carpet on some floors using adhesive, following prescribed method. | —0 |
Nail tack strips around area to be carpeted or use old strips to attach edges of new carpet. | —0 |
Fasten metal treads across door openings or where carpet meets flooring to hold carpet in place. | —0 |
Measure, cut and install tackless strips along the baseboard or wall. | —0 |
Move furniture from area to be carpeted and remove old carpet and padding. | —0 |
Cut and bind material. | —0 |
Clean up before and after installation, including vacuuming carpet and discarding remnant pieces. | —0 |
Values in this tab are predicted labels, not observations. Eloundou et al. (2023) published two rating regimes — human raters and GPT-4 — and the β shown here is derived from the GPT-4 rater basis alone; the same task can take a different value under the other regime. The unit and the meaning differ from the observed shares (%) in the other tabs, so do not place them on the same axis.
| Task | βE1 + 0.5 × E2 |
|---|---|
Take measurements and study floor sketches to calculate the area to be carpeted and the amount of material needed.O*NET Task ID 2839 | 0.5 |
Draw building diagrams and record dimensions.O*NET Task ID 2845 | 0.5 |
Join edges of carpet and seam edges where necessary, by sewing or by using tape with glue and heated carpet iron.O*NET Task ID 2833 | 0.0 |
Cut and trim carpet to fit along wall edges, openings, and projections, finishing the edges with a wall trimmer.O*NET Task ID 2834 | 0.0 |
Inspect the surface to be covered to determine its condition, and correct any imperfections that might show through carpet or cause carpet to wear unevenly.O*NET Task ID 2835 | 0.0 |
Roll out, measure, mark, and cut carpeting to size with a carpet knife, following floor sketches and allowing extra carpet for final fitting.O*NET Task ID 2836 | 0.0 |
Plan the layout of the carpet, allowing for expected traffic patterns and placing seams for best appearance and longest wear.O*NET Task ID 2837 | 0.0 |
Stretch carpet to align with walls and ensure a smooth surface, and press carpet in place over tack strips or use staples, tape, tacks or glue to hold carpet in place.O*NET Task ID 2838 | 0.0 |
Cut carpet padding to size and install padding, following prescribed method.O*NET Task ID 2840 | 0.0 |
Install carpet on some floors using adhesive, following prescribed method.O*NET Task ID 2841 | 0.0 |
Nail tack strips around area to be carpeted or use old strips to attach edges of new carpet.O*NET Task ID 2842 | 0.0 |
Fasten metal treads across door openings or where carpet meets flooring to hold carpet in place.O*NET Task ID 2843 | 0.0 |
Measure, cut and install tackless strips along the baseboard or wall.O*NET Task ID 2844 | 0.0 |
Move furniture from area to be carpeted and remove old carpet and padding.O*NET Task ID 2846 | 0.0 |
Cut and bind material.O*NET Task ID 2847 | 0.0 |
Clean up before and after installation, including vacuuming carpet and discarding remnant pieces.O*NET Task ID 20142 | 0.0 |
β = E1 + 0.5 × E2 · E1 = tasks where direct LLM access alone cuts time by at least 50%, E2 = tasks where software built on top of an LLM cuts time by at least 50%. Values take only 0 / 0.5 / 1.0.
Data sources & licenses — O*NET®, Anthropic Economic Index, Eloundou et al. (2023): see full notices on the Credits page