耐火材料修理工
建設・メンテナンス・修理AI露出度
- データ出典: BLS公表時点: 2026-08
低い· 相対
低い4段階の相対区分非常に高い職業群単位の値
尺度・母数・出典
4段階の相対区分（低い / 中程度 / 高い / 非常に高い）
BLS雇用見通し表の詳細職業831件が母数。値は NEM(全国雇用マトリクス)コード単位で付与されるため、同じ NEM コードの職業は同じバンドになります
- データ出典: Anthropic公表時点: 2026-03
0.000
0.000ここに掲載された値の範囲0.745尺度・母数・出典
- データ出典: ILO公表時点: 2025
0.09
0.09ここに掲載された値の範囲0.70職業群単位の値
尺度・母数・出典
生成AI露出度指数、公開されたまま0–1
ISCO-08の職業小分類単位 — 同じコードの職業はすべて同じ値
当サイトの算出であり、ILOが公表した数値ではありません。当サイトがILOデータセットに結び付けた職業1,012件のうち、この値以上のものは100%です。
この出典がどのような性格の値か
BLSの区分は絶対水準ではなく相対順位であり、一次測定でもありません。複数の既存研究が付けた職業別パーセンタイル順位を4段階にまとめた値です。雇用や賃金の予測でもなく、導入確率でもなく、自動化と増強を区別しません。
Task-level exposure
Values in this tab are predicted labels, not observations. Eloundou et al. (2023) published two rating regimes — human raters and GPT-4 — and the β shown here is derived from the GPT-4 rater basis alone; the same task can take a different value under the other regime.
| Task | βE1 + 0.5 × E2 |
|---|---|
Reline or repair ladles and pouring spouts with refractory clay, using trowels.O*NET Task ID 13819 | 0.0 |
Chip slag from linings of ladles or remove linings when beyond repair, using hammers and chisels.O*NET Task ID 13820 | 0.0 |
Mix specified amounts of sand, clay, mortar powder, and water to form refractory clay or mortar, using shovels or mixing machines.O*NET Task ID 13821 | 0.0 |
Measure furnace walls to determine dimensions and cut required number of sheets from plastic block, using saws.O*NET Task ID 13822 | 0.0 |
Tighten locknuts holding refractory stopper assemblies together, spread mortar on jackets to seal sleeve joints, and dry mortar in ovens.O*NET Task ID 13823 | 0.0 |
Dry and bake new linings by placing inverted linings over burners, building fires in ladles, or by using blowtorches.O*NET Task ID 13824 | 0.0 |
Remove worn or damaged plastic block refractory linings of furnaces, using hand tools.O*NET Task ID 13825 | 0.0 |
Fasten stopper heads to rods with metal pins to assemble refractory stoppers used to plug pouring nozzles of steel ladles.O*NET Task ID 13826 | 0.0 |
Climb scaffolding, carrying hoses, and spray surfaces of cupolas with refractory mixtures, using spray equipment.O*NET Task ID 13827 | 0.0 |
Drill holes in furnace walls, bolt overlapping layers of plastic to walls, and hammer surfaces to compress layers into solid sheets.O*NET Task ID 13828 | 0.0 |
Spread mortar on stopper heads and rods, using trowels, and slide brick sleeves over rods to form refractory jackets.O*NET Task ID 13829 | 0.0 |
Dump and tamp clay in molds, using tamping tools.O*NET Task ID 13830 | 0.0 |
Disassemble molds, and cut, chip, and smooth clay structures such as floaters, drawbars, and L-blocks.O*NET Task ID 13831 | 0.0 |
Transfer clay structures to curing ovens, melting tanks, and drawing kilns, using forklifts.O*NET Task ID 13832 | 0.0 |
Install preformed metal scaffolding in interiors of cupolas, using hand tools.O*NET Task ID 13833 | 0.0 |
Install clay structures in melting tanks and drawing kilns to control the flow and temperature of molten glass, using hoists and hand tools.O*NET Task ID 13834 | 0.0 |
β = E1 + 0.5 × E2 · E1 = tasks where direct LLM access alone cuts time by at least 50%, E2 = tasks where software built on top of an LLM cuts time by at least 50%. Values take only 0 / 0.5 / 1.0.
Data sources & licenses — O*NET®, Eloundou et al. (2023): see full notices on the Credits page