Técnicos HVAC

Construção, Manutenção e Reparo

Exposição à IA

  • Fonte dos dados: BLSPublicado: 2026-08

    Moderado· relativa

    BaixoQuatro faixas relativasMuito alto

    Valor por grupo ocupacional

    Escala, base e fonte

    Quatro faixas relativas (Baixo / Moderado / Alto / Muito alto)

    831 ocupações detalhadas da tabela de projeções de emprego do BLS. O valor é atribuído por código da National Employment Matrix (NEM), pelo que as ocupações que partilham um código NEM recebem a mesma banda

    Conjunto de dados de origem (transferência XLSX)

  • Fonte dos dados: AnthropicPublicado: 2026-03

    0.019

    0.000Intervalo dos valores aqui apresentados0.745
    Escala, base e fonte

    Índice de exposição observada, 0–1 tal como publicado

    Mapeado sobre tarefas O*NET

    Conjunto de dados de origem

  • Fonte dos dados: ILOPublicado: 2025

    0.21

    0.09Intervalo dos valores aqui apresentados0.70

    Valor por grupo ocupacional

    Escala, base e fonte

    Índice de exposição à IA generativa, 0–1 tal como publicado

    Grupo de base CITP-08 — todas as ocupações com o mesmo código recebem este valor

    Calculado por este site, não publicado pela OIT: das 1.012 ocupações que este site liga ao conjunto de dados da OIT, 82% atingem ou superam este valor.

    Conjunto de dados de origem

Que tipo de valor esta fonte publica

A categoria de BLS é uma posição relativa, não um nível absoluto, e também não é uma medição de primeira mão: agrupa em quatro faixas as posições percentis da ocupação em vários estudos publicados. Não é uma previsão de emprego ou de salários, não é uma probabilidade de adoção e não distingue automação de aumento.

Task-level exposure

Apenas tarefas expostas
TaskClaude.aiRaw / share %
Study blueprints, design specifications, or manufacturers' recommendations to ascertain the configuration of heating or cooling equipment components and to ensure the proper installation of components.

49-9021

0.009851.7
Insulate shells and cabinets of systems.

49-9021

0.006333.1
Test electrical circuits or components for continuity, using electrical test equipment.

49-9021

0.002915.2
Not observed on any surface — 44 task(s) — These tasks have no row in the source for this release. The 0 in the share row is a display-stage composition ratio; absence is what the — in the raw row states.
Repair or replace defective equipment, components, or wiring.
—0
Inspect and test systems to verify system compliance with plans and specifications or to detect and locate malfunctions.
—0
Test pipe or tubing joints or connections for leaks, using pressure gauge or soap-and-water solution.
—0
Recommend, develop, or perform preventive or general maintenance procedures, such as cleaning, power-washing, or vacuuming equipment, oiling parts, or changing filters.
—0
Lay out and connect electrical wiring between controls and equipment, according to wiring diagrams, using electrician's hand tools.
—0
Cut or drill holes in floors, walls, or roof to install equipment, using power saws or drills.
—0
Measure, cut, thread, or bend pipe or tubing, using pipe fitter's tools.
—0
Fabricate, assemble, or install duct work or chassis parts, using portable metal-working tools or welding equipment.
—0
Install and test automatic, programmable, or wireless thermostats in residential or commercial buildings to minimize energy usage for heating or cooling.
—0
Install dehumidifiers or related equipment for spaces that require cool, dry air to operate efficiently, such as computer rooms.
—0
Install magnetic-centrifugal chillers, compressors, or related equipment to cool air temperatures through the use of recirculating water.
—0
Install or repair air purification systems, such as specialized filters or ultraviolet (UV) light purification systems.
—0
Install radiator controls for room-level zone control heating of residential or commercial buildings.
—0
Repair or service heating, ventilating, and air conditioning (HVAC) systems to improve efficiency, such as by changing filters, cleaning ducts, or refilling non-toxic refrigerants.
—0
Discuss heating or cooling system malfunctions with users to isolate problems or to verify that repairs corrected malfunctions.
—0
Install, connect, or adjust thermostats, humidistats, or timers.
—0
Connect heating or air conditioning equipment to fuel, water, or refrigerant source to form complete circuit.
—0
Comply with all applicable standards, policies, or procedures, such as safety procedures or the maintenance of a clean work area.
—0
Install auxiliary components to heating or cooling equipment, such as expansion or discharge valves, air ducts, pipes, blowers, dampers, flues, or stokers.
—0
Record and report time, materials, faults, deficiencies, or other unusual occurrences on work orders.
—0
Adjust system controls to settings recommended by manufacturer to balance system.
—0
Assemble, position, and mount heating or cooling equipment, following blueprints or manufacturer's specifications.
—0
Install or repair self-contained ground source heat pumps or hybrid ground or air source heat pumps to minimize carbon-based energy consumption and reduce carbon emissions.
—0
Wrap pipes, securing insulation in place with cement or wire bands.
—0
Braze or solder parts to repair defective joints and leaks.
—0
Observe and test system operation, using gauges and instruments.
—0
Test lines, components, and connections for leaks.
—0
Dismantle malfunctioning systems and test components, using electrical, mechanical, and pneumatic testing equipment.
—0
Adjust or replace worn or defective mechanisms and parts and reassemble repaired systems.
—0
Read blueprints to determine location, size, capacity, and type of components needed to build refrigeration system.
—0
Supervise and instruct assistants.
—0
Install wiring to connect components to an electric power source.
—0
Perform mechanical overhauls and refrigerant reclaiming.
—0
Cut, bend, thread, and connect pipe to functional components and water, power, or refrigeration system.
—0
Adjust valves according to specifications and charge system with proper type of refrigerant by pumping the specified gas or fluid into the system.
—0
Estimate, order, pick up, deliver, and install materials and supplies needed to maintain equipment in good working condition.
—0
Install expansion and control valves, using acetylene torches and wrenches.
—0
Mount compressor, condenser, and other components in specified locations on frames, using hand tools and acetylene welding equipment.
—0
Keep records of repairs and replacements made and causes of malfunctions.
—0
Lay out reference points for installation of structural and functional components, using measuring instruments.
—0
Schedule work with customers and initiate work orders, house requisitions, and orders from stock.
—0
Fabricate and assemble structural and functional components of refrigeration system, using hand tools, power tools, and welding equipment.
—0
Lift and align components into position, using hoist or block and tackle.
—0
Drill holes and install mounting brackets and hangers into floor and walls of building.
—0

Data sources & licenses — O*NET®, Anthropic Economic Index, Eloundou et al. (2023): see full notices on the Credits page

Informação ocupacional