রিফ্র্যাক্টরি উপকরণ মেরামতকারী
নির্মাণ, রক্ষণাবেক্ষণ ও মেরামতAI এক্সপোজার
- ডেটার উৎস: BLSপ্রকাশকাল: 2026-08
কম· আপেক্ষিক
কমচারটি আপেক্ষিক স্তরঅত্যন্ত উচ্চপেশা-গোষ্ঠী পর্যায়ের মান
স্কেল, ভিত্তি ও উৎস
চারটি আপেক্ষিক স্তর (কম / মাঝারি / উচ্চ / অত্যন্ত উচ্চ)
BLS কর্মসংস্থান পূর্বাভাস সারণির 831টি বিস্তারিত পেশার ভিত্তিতে। মান NEM (ন্যাশনাল এমপ্লয়মেন্ট ম্যাট্রিক্স) কোড অনুযায়ী দেওয়া হয়, তাই একই NEM কোডের পেশাগুলি একই ব্যান্ড পায়
- ডেটার উৎস: Anthropicপ্রকাশকাল: 2026-03
0.000
0.000এখানে থাকা মানগুলোর পরিসর0.745স্কেল, ভিত্তি ও উৎস
- ডেটার উৎস: ILOপ্রকাশকাল: 2025
0.09
0.09এখানে থাকা মানগুলোর পরিসর0.70পেশা-গোষ্ঠী পর্যায়ের মান
স্কেল, ভিত্তি ও উৎস
জেনারেটিভ AI এক্সপোজার সূচক, প্রকাশিত রূপে 0–1
ISCO-08 ইউনিট গ্রুপ — একই কোডের সব পেশা এই মানই পায়
এটি এই সাইটের হিসাব, ILO-এর প্রকাশিত সংখ্যা নয়: এই সাইট ILO ডেটাসেটের সঙ্গে যুক্ত করা ১,০১২টি পেশার মধ্যে 100% এই মানের সমান বা তার বেশি।
এই উৎস কী ধরনের মান প্রকাশ করে
BLS-এর শ্রেণিবিভাগ একটি আপেক্ষিক র্যাঙ্ক, পরম মাত্রা নয়, এবং এটি সরাসরি পরিমাপও নয়: এটি কয়েকটি প্রকাশিত গবেষণায় পাওয়া পেশার পার্সেন্টাইল র্যাঙ্কগুলিকে চারটি স্তরে ভাগ করে। এটি কর্মসংস্থান বা মজুরির পূর্বাভাস নয়, গ্রহণের সম্ভাবনাও নয়, এবং এটি স্বয়ংক্রিয়তা ও সম্প্রসারণের মধ্যে পার্থক্য করে না।
Task-level exposure
Values in this tab are predicted labels, not observations. Eloundou et al. (2023) published two rating regimes — human raters and GPT-4 — and the β shown here is derived from the GPT-4 rater basis alone; the same task can take a different value under the other regime.
| Task | βE1 + 0.5 × E2 |
|---|---|
Reline or repair ladles and pouring spouts with refractory clay, using trowels.O*NET Task ID 13819 | 0.0 |
Chip slag from linings of ladles or remove linings when beyond repair, using hammers and chisels.O*NET Task ID 13820 | 0.0 |
Mix specified amounts of sand, clay, mortar powder, and water to form refractory clay or mortar, using shovels or mixing machines.O*NET Task ID 13821 | 0.0 |
Measure furnace walls to determine dimensions and cut required number of sheets from plastic block, using saws.O*NET Task ID 13822 | 0.0 |
Tighten locknuts holding refractory stopper assemblies together, spread mortar on jackets to seal sleeve joints, and dry mortar in ovens.O*NET Task ID 13823 | 0.0 |
Dry and bake new linings by placing inverted linings over burners, building fires in ladles, or by using blowtorches.O*NET Task ID 13824 | 0.0 |
Remove worn or damaged plastic block refractory linings of furnaces, using hand tools.O*NET Task ID 13825 | 0.0 |
Fasten stopper heads to rods with metal pins to assemble refractory stoppers used to plug pouring nozzles of steel ladles.O*NET Task ID 13826 | 0.0 |
Climb scaffolding, carrying hoses, and spray surfaces of cupolas with refractory mixtures, using spray equipment.O*NET Task ID 13827 | 0.0 |
Drill holes in furnace walls, bolt overlapping layers of plastic to walls, and hammer surfaces to compress layers into solid sheets.O*NET Task ID 13828 | 0.0 |
Spread mortar on stopper heads and rods, using trowels, and slide brick sleeves over rods to form refractory jackets.O*NET Task ID 13829 | 0.0 |
Dump and tamp clay in molds, using tamping tools.O*NET Task ID 13830 | 0.0 |
Disassemble molds, and cut, chip, and smooth clay structures such as floaters, drawbars, and L-blocks.O*NET Task ID 13831 | 0.0 |
Transfer clay structures to curing ovens, melting tanks, and drawing kilns, using forklifts.O*NET Task ID 13832 | 0.0 |
Install preformed metal scaffolding in interiors of cupolas, using hand tools.O*NET Task ID 13833 | 0.0 |
Install clay structures in melting tanks and drawing kilns to control the flow and temperature of molten glass, using hoists and hand tools.O*NET Task ID 13834 | 0.0 |
β = E1 + 0.5 × E2 · E1 = tasks where direct LLM access alone cuts time by at least 50%, E2 = tasks where software built on top of an LLM cuts time by at least 50%. Values take only 0 / 0.5 / 1.0.
Data sources & licenses — O*NET®, Eloundou et al. (2023): see full notices on the Credits page