Albaniles de Cemento y Acabadores de Concreto
Construcción, Mantenimiento y ReparaciónExposición a la IA
- Fuente de datos: BLSPublicado: 2026-08
Bajo· relativa
BajoCuatro bandas relativasMuy altoValor por grupo ocupacional
Escala, base y fuente
Cuatro bandas relativas (Bajo / Moderado / Alto / Muy alto)
831 ocupaciones detalladas de la tabla de proyecciones de empleo de BLS. El valor se asigna por código de la National Employment Matrix (NEM), de modo que las ocupaciones que comparten un código NEM reciben la misma banda
- Fuente de datos: AnthropicPublicado: 2026-03
0.000
0.000Rango de los valores aquí recogidos0.745Escala, base y fuente
Índice de exposición observada, 0–1 tal como se publica
Mapeado sobre tareas de O*NET
- Fuente de datos: ILOPublicado: 2025
0.10
0.09Rango de los valores aquí recogidos0.70Valor por grupo ocupacional
Escala, base y fuente
Índice de exposición a la IA generativa, 0–1 tal como se publica
Grupo primario de la CIUO-08 — todas las ocupaciones con ese código reciben este valor
Calculado por este sitio, no publicado por la OIT: de las 1012 ocupaciones que este sitio vincula al conjunto de datos de la OIT, un 98% alcanza o supera este valor.
Qué tipo de cifra publica esta fuente
La categoría de BLS es un rango relativo, no un nivel absoluto, y tampoco es una medición de primera mano: agrupa en cuatro bandas los rangos percentiles de la ocupación en varios estudios publicados. No es una previsión de empleo ni de salarios, no es una probabilidad de adopción y no distingue entre automatización y aumento.
Task-level exposure
Values in this tab are predicted labels, not observations. Eloundou et al. (2023) published two rating regimes — human raters and GPT-4 — and the β shown here is derived from the GPT-4 rater basis alone; the same task can take a different value under the other regime. The unit and the meaning differ from the observed shares (%) in the other tabs, so do not place them on the same axis.
| Task | βE1 + 0.5 × E2 |
|---|---|
Check the forms that hold the concrete to see that they are properly constructed.O*NET Task ID 7047 | 0.0 |
Set the forms that hold concrete to the desired pitch and depth, and align them.O*NET Task ID 7048 | 0.0 |
Spread, level, and smooth concrete, using rake, shovel, hand or power trowel, hand or power screed, and float.O*NET Task ID 7049 | 0.0 |
Mold expansion joints and edges, using edging tools, jointers, and straightedge.O*NET Task ID 7050 | 0.0 |
Monitor how the wind, heat, or cold affect the curing of the concrete throughout the entire process.O*NET Task ID 7051 | 0.0 |
Signal truck driver to position truck to facilitate pouring concrete, and move chute to direct concrete on forms.O*NET Task ID 7052 | 0.0 |
Produce rough concrete surface, using broom.O*NET Task ID 7053 | 0.0 |
Operate power vibrator to compact concrete.O*NET Task ID 7054 | 0.0 |
Direct the casting of the concrete and supervise laborers who use shovels or special tools to spread it.O*NET Task ID 7055 | 0.0 |
Mix cement, sand, and water to produce concrete, grout, or slurry, using hoe, trowel, tamper, scraper, or concrete-mixing machine.O*NET Task ID 7056 | 0.0 |
Cut out damaged areas, drill holes for reinforcing rods, and position reinforcing rods to repair concrete, using power saw and drill.O*NET Task ID 7057 | 0.0 |
Wet concrete surface, and rub with stone to smooth surface and obtain specified finish.O*NET Task ID 7058 | 0.0 |
Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth, using trowel.O*NET Task ID 7059 | 0.0 |
Clean chipped area, using wire brush, and feel and observe surface to determine if it is rough or uneven.O*NET Task ID 7060 | 0.0 |
Apply hardening and sealing compounds to cure surface of concrete, and waterproof or restore surface.O*NET Task ID 7061 | 0.0 |
Chip, scrape, and grind high spots, ridges, and rough projections to finish concrete, using pneumatic chisels, power grinders, or hand tools.O*NET Task ID 7062 | 0.0 |
Spread roofing paper on surface of foundation, and spread concrete onto roofing paper with trowel to form terrazzo base.O*NET Task ID 7063 | 0.0 |
Build wooden molds, and clamp molds around area to be repaired, using hand tools.O*NET Task ID 7064 | 0.0 |
Sprinkle colored marble or stone chips, powdered steel, or coloring powder over surface to produce prescribed finish.O*NET Task ID 7065 | 0.0 |
Cut metal division strips, and press them into terrazzo base so that top edges form desired design or pattern.O*NET Task ID 7066 | 0.0 |
Fabricate concrete beams, columns, and panels.O*NET Task ID 7067 | 0.0 |
Waterproof or restore concrete surfaces, using appropriate compounds.O*NET Task ID 7068 | 0.0 |
Install anchor bolts, steel plates, door sills and other fixtures in freshly poured concrete or pattern or stamp the surface to provide a decorative finish.O*NET Task ID 7069 | 0.0 |
Apply muriatic acid to clean surface, and rinse with water.O*NET Task ID 7070 | 0.0 |
Push roller over surface to embed chips in surface.O*NET Task ID 7071 | 0.0 |
Polish surface, using polishing or surfacing machine.O*NET Task ID 7072 | 0.0 |
β = E1 + 0.5 × E2 · E1 = tasks where direct LLM access alone cuts time by at least 50%, E2 = tasks where software built on top of an LLM cuts time by at least 50%. Values take only 0 / 0.5 / 1.0.
Data sources & licenses — O*NET®, Eloundou et al. (2023): see full notices on the Credits page