Técnicos HVAC

Construcción, Mantenimiento y Reparación

Exposición a la IA

  • Fuente de datos: BLSPublicado: 2026-08

    Moderado· relativa

    BajoCuatro bandas relativasMuy alto

    Valor por grupo ocupacional

    Escala, base y fuente

    Cuatro bandas relativas (Bajo / Moderado / Alto / Muy alto)

    831 ocupaciones detalladas de la tabla de proyecciones de empleo de BLS. El valor se asigna por código de la National Employment Matrix (NEM), de modo que las ocupaciones que comparten un código NEM reciben la misma banda

    Conjunto de datos de origen (descarga XLSX)

  • Fuente de datos: AnthropicPublicado: 2026-03

    0.019

    0.000Rango de los valores aquí recogidos0.745
    Escala, base y fuente

    Índice de exposición observada, 0–1 tal como se publica

    Mapeado sobre tareas de O*NET

    Conjunto de datos de origen

  • Fuente de datos: ILOPublicado: 2025

    0.21

    0.09Rango de los valores aquí recogidos0.70

    Valor por grupo ocupacional

    Escala, base y fuente

    Índice de exposición a la IA generativa, 0–1 tal como se publica

    Grupo primario de la CIUO-08 — todas las ocupaciones con ese código reciben este valor

    Calculado por este sitio, no publicado por la OIT: de las 1012 ocupaciones que este sitio vincula al conjunto de datos de la OIT, un 82% alcanza o supera este valor.

    Conjunto de datos de origen

Qué tipo de cifra publica esta fuente

La categoría de BLS es un rango relativo, no un nivel absoluto, y tampoco es una medición de primera mano: agrupa en cuatro bandas los rangos percentiles de la ocupación en varios estudios publicados. No es una previsión de empleo ni de salarios, no es una probabilidad de adopción y no distingue entre automatización y aumento.

Task-level exposure

Solo tareas expuestas
TaskClaude.aiRaw / share %APIRaw / share %
Inspect and test systems to verify system compliance with plans and specifications or to detect and locate malfunctions.

49-9021

0.00000.00.0100100.0
Record and report time, materials, faults, deficiencies, or other unusual occurrences on work orders.

49-9021

0.00000.00.00000.0
Comply with all applicable standards, policies, or procedures, such as safety procedures or the maintenance of a clean work area.
—00.00000.0
Not observed on any surface — 27 task(s) — These tasks have no row in the source for this release. The 0 in the share row is a display-stage composition ratio; absence is what the — in the raw row states.
Test electrical circuits or components for continuity, using electrical test equipment.
—0—0
Repair or replace defective equipment, components, or wiring.
—0—0
Discuss heating or cooling system malfunctions with users to isolate problems or to verify that repairs corrected malfunctions.
—0—0
Connect heating or air conditioning equipment to fuel, water, or refrigerant source to form complete circuit.
—0—0
Install, connect, or adjust thermostats, humidistats, or timers.
—0—0
Study blueprints, design specifications, or manufacturers' recommendations to ascertain the configuration of heating or cooling equipment components and to ensure the proper installation of components.
—0—0
Install auxiliary components to heating or cooling equipment, such as expansion or discharge valves, air ducts, pipes, blowers, dampers, flues, or stokers.
—0—0
Braze or solder parts to repair defective joints and leaks.
—0—0
Lay out and connect electrical wiring between controls and equipment, according to wiring diagrams, using electrician's hand tools.
—0—0
Perform mechanical overhauls and refrigerant reclaiming.
—0—0
Adjust system controls to settings recommended by manufacturer to balance system.
—0—0
Install expansion and control valves, using acetylene torches and wrenches.
—0—0
Install dehumidifiers or related equipment for spaces that require cool, dry air to operate efficiently, such as computer rooms.
—0—0
Recommend, develop, or perform preventive or general maintenance procedures, such as cleaning, power-washing, or vacuuming equipment, oiling parts, or changing filters.
—0—0
Cut or drill holes in floors, walls, or roof to install equipment, using power saws or drills.
—0—0
Mount compressor, condenser, and other components in specified locations on frames, using hand tools and acetylene welding equipment.
—0—0
Measure, cut, thread, or bend pipe or tubing, using pipe fitter's tools.
—0—0
Keep records of repairs and replacements made and causes of malfunctions.
—0—0
Estimate, order, pick up, deliver, and install materials and supplies needed to maintain equipment in good working condition.
—0—0
Schedule work with customers and initiate work orders, house requisitions, and orders from stock.
—0—0
Supervise and instruct assistants.
—0—0
Lay out reference points for installation of structural and functional components, using measuring instruments.
—0—0
Lift and align components into position, using hoist or block and tackle.
—0—0
Install or repair self-contained ground source heat pumps or hybrid ground or air source heat pumps to minimize carbon-based energy consumption and reduce carbon emissions.
—0—0
Install or repair air purification systems, such as specialized filters or ultraviolet (UV) light purification systems.
—0—0
Repair or service heating, ventilating, and air conditioning (HVAC) systems to improve efficiency, such as by changing filters, cleaning ducts, and refilling non-toxic refrigerants.
—0—0
Test pipes, lines, components, and connections for leaks.
—0—0

Data sources & licenses — O*NET®, Anthropic Economic Index, Eloundou et al. (2023): see full notices on the Credits page

Información ocupacional