Reparadores de Materiales Refractarios

Construcción, Mantenimiento y Reparación

Exposición a la IA

  • Fuente de datos: BLSPublicado: 2026-08

    Bajo· relativa

    BajoCuatro bandas relativasMuy alto

    Valor por grupo ocupacional

    Escala, base y fuente

    Cuatro bandas relativas (Bajo / Moderado / Alto / Muy alto)

    831 ocupaciones detalladas de la tabla de proyecciones de empleo de BLS. El valor se asigna por código de la National Employment Matrix (NEM), de modo que las ocupaciones que comparten un código NEM reciben la misma banda

    Conjunto de datos de origen (descarga XLSX)

  • Fuente de datos: AnthropicPublicado: 2026-03

    0.000

    0.000Rango de los valores aquí recogidos0.745
    Escala, base y fuente

    Índice de exposición observada, 0–1 tal como se publica

    Mapeado sobre tareas de O*NET

    Conjunto de datos de origen

  • Fuente de datos: ILOPublicado: 2025

    0.09

    0.09Rango de los valores aquí recogidos0.70

    Valor por grupo ocupacional

    Escala, base y fuente

    Índice de exposición a la IA generativa, 0–1 tal como se publica

    Grupo primario de la CIUO-08 — todas las ocupaciones con ese código reciben este valor

    Calculado por este sitio, no publicado por la OIT: de las 1012 ocupaciones que este sitio vincula al conjunto de datos de la OIT, un 100% alcanza o supera este valor.

    Conjunto de datos de origen

Qué tipo de cifra publica esta fuente

La categoría de BLS es un rango relativo, no un nivel absoluto, y tampoco es una medición de primera mano: agrupa en cuatro bandas los rangos percentiles de la ocupación en varios estudios publicados. No es una previsión de empleo ni de salarios, no es una probabilidad de adopción y no distingue entre automatización y aumento.

Task-level exposure

Values in this tab are predicted labels, not observations. Eloundou et al. (2023) published two rating regimes — human raters and GPT-4 — and the β shown here is derived from the GPT-4 rater basis alone; the same task can take a different value under the other regime.

TaskβE1 + 0.5 × E2
Reline or repair ladles and pouring spouts with refractory clay, using trowels.

O*NET Task ID 13819

0.0
Chip slag from linings of ladles or remove linings when beyond repair, using hammers and chisels.

O*NET Task ID 13820

0.0
Mix specified amounts of sand, clay, mortar powder, and water to form refractory clay or mortar, using shovels or mixing machines.

O*NET Task ID 13821

0.0
Measure furnace walls to determine dimensions and cut required number of sheets from plastic block, using saws.

O*NET Task ID 13822

0.0
Tighten locknuts holding refractory stopper assemblies together, spread mortar on jackets to seal sleeve joints, and dry mortar in ovens.

O*NET Task ID 13823

0.0
Dry and bake new linings by placing inverted linings over burners, building fires in ladles, or by using blowtorches.

O*NET Task ID 13824

0.0
Remove worn or damaged plastic block refractory linings of furnaces, using hand tools.

O*NET Task ID 13825

0.0
Fasten stopper heads to rods with metal pins to assemble refractory stoppers used to plug pouring nozzles of steel ladles.

O*NET Task ID 13826

0.0
Climb scaffolding, carrying hoses, and spray surfaces of cupolas with refractory mixtures, using spray equipment.

O*NET Task ID 13827

0.0
Drill holes in furnace walls, bolt overlapping layers of plastic to walls, and hammer surfaces to compress layers into solid sheets.

O*NET Task ID 13828

0.0
Spread mortar on stopper heads and rods, using trowels, and slide brick sleeves over rods to form refractory jackets.

O*NET Task ID 13829

0.0
Dump and tamp clay in molds, using tamping tools.

O*NET Task ID 13830

0.0
Disassemble molds, and cut, chip, and smooth clay structures such as floaters, drawbars, and L-blocks.

O*NET Task ID 13831

0.0
Transfer clay structures to curing ovens, melting tanks, and drawing kilns, using forklifts.

O*NET Task ID 13832

0.0
Install preformed metal scaffolding in interiors of cupolas, using hand tools.

O*NET Task ID 13833

0.0
Install clay structures in melting tanks and drawing kilns to control the flow and temperature of molten glass, using hoists and hand tools.

O*NET Task ID 13834

0.0

β = E1 + 0.5 × E2 · E1 = tasks where direct LLM access alone cuts time by at least 50%, E2 = tasks where software built on top of an LLM cuts time by at least 50%. Values take only 0 / 0.5 / 1.0.

Data sources & licenses — O*NET®, Eloundou et al. (2023): see full notices on the Credits page

Información ocupacional