Aplicadores de Fita
Construção, Manutenção e ReparoExposição à IA
- Fonte dos dados: BLSPublicado: 2026-08
Baixo· relativa
BaixoQuatro faixas relativasMuito altoValor por grupo ocupacional
Escala, base e fonte
Quatro faixas relativas (Baixo / Moderado / Alto / Muito alto)
831 ocupações detalhadas da tabela de projeções de emprego do BLS. O valor é atribuído por código da National Employment Matrix (NEM), pelo que as ocupações que partilham um código NEM recebem a mesma banda
- Fonte dos dados: AnthropicPublicado: 2026-03
0.000
0.000Intervalo dos valores aqui apresentados0.745Escala, base e fonte
Índice de exposição observada, 0–1 tal como publicado
Mapeado sobre tarefas O*NET
- Fonte dos dados: ILOPublicado: 2025
0.11
0.09Intervalo dos valores aqui apresentados0.70Valor por grupo ocupacional
Escala, base e fonte
Índice de exposição à IA generativa, 0–1 tal como publicado
Grupo de base CITP-08 — todas as ocupações com o mesmo código recebem este valor
Calculado por este site, não publicado pela OIT: das 1.012 ocupações que este site liga ao conjunto de dados da OIT, 98% atingem ou superam este valor.
Que tipo de valor esta fonte publica
A categoria de BLS é uma posição relativa, não um nível absoluto, e também não é uma medição de primeira mão: agrupa em quatro faixas as posições percentis da ocupação em vários estudos publicados. Não é uma previsão de emprego ou de salários, não é uma probabilidade de adoção e não distingue automação de aumento.
Task-level exposure
Values in this tab are predicted labels, not observations. Eloundou et al. (2023) published two rating regimes — human raters and GPT-4 — and the β shown here is derived from the GPT-4 rater basis alone; the same task can take a different value under the other regime. The unit and the meaning differ from the observed shares (%) in the other tabs, so do not place them on the same axis.
| Task | βE1 + 0.5 × E2 |
|---|---|
Remove extra compound after surfaces have been covered sufficiently.O*NET Task ID 13529 | 0.0 |
Spread sealing compound between boards or panels or over cracks, holes, nail heads, or screw heads, using trowels, broadknives, or spatulas.O*NET Task ID 13530 | 0.0 |
Press paper tape over joints to embed tape into sealing compound and to seal joints.O*NET Task ID 13531 | 0.0 |
Mix sealing compounds by hand or with portable electric mixers.O*NET Task ID 13532 | 0.0 |
Spread and smooth cementing material over tape, using trowels or floating machines to blend joints with wall surfaces.O*NET Task ID 13533 | 0.0 |
Seal joints between plasterboard or other wallboard to prepare wall surfaces for painting or papering.O*NET Task ID 13534 | 0.0 |
Sand or patch nicks or cracks in plasterboard or wallboard.O*NET Task ID 13535 | 0.0 |
Use mechanical applicators that spread compounds and embed tape in one operation.O*NET Task ID 13536 | 0.0 |
Apply additional coats to fill in holes and make surfaces smooth.O*NET Task ID 13537 | 0.0 |
Install metal molding at wall corners to secure wallboard.O*NET Task ID 13538 | 0.0 |
Sand rough spots of dried cement between applications of compounds.O*NET Task ID 13539 | 0.0 |
Countersink nails or screws below surfaces of walls before applying sealing compounds, using hammers or screwdrivers.O*NET Task ID 13540 | 0.0 |
Select the correct sealing compound or tape.O*NET Task ID 13541 | 0.0 |
Apply texturizing compounds or primers to walls or ceilings before final finishing, using trowels, brushes, rollers, or spray guns.O*NET Task ID 13542 | 0.0 |
Check adhesives to ensure that they will work and will remain durable.O*NET Task ID 13543 | 0.0 |
Work on high ceilings, using scaffolding or other tools, such as stilts.O*NET Task ID 20788 | 0.0 |
β = E1 + 0.5 × E2 · E1 = tasks where direct LLM access alone cuts time by at least 50%, E2 = tasks where software built on top of an LLM cuts time by at least 50%. Values take only 0 / 0.5 / 1.0.
Data sources & licenses — O*NET®, Eloundou et al. (2023): see full notices on the Credits page