耐火材料修理工
建筑、维护与维修AI暴露度
- 数据来源: BLS发布时间: 2026-08
低· 相对
低四级相对区间很高职业群单位数值
尺度 · 母数 · 来源
四级相对类别（低 / 中等 / 高 / 很高）
以BLS就业预测表中831个细分职业为基数。取值按 NEM（全国就业矩阵）代码给定，因此共用同一 NEM 代码的职业得到相同分档
- 数据来源: Anthropic发布时间: 2026-03
0.000
0.000此处所载数值的范围0.745尺度 · 母数 · 来源
- 数据来源: ILO发布时间: 2025
0.09
0.09此处所载数值的范围0.70职业群单位数值
尺度 · 母数 · 来源
生成式AI暴露度指数，按发布原值0–1
ISCO-08职业小类单位 — 共用同一代码的职业取值相同
本站计算，并非国际劳工组织发布的数值。在本站与 ILO 数据集相连的 1,012 个职业中，达到或高于此值的占 100%。
该来源发布的是什么性质的数值
BLS的类别是相对排位而非绝对水平，也不是一手测量：它把多项已发表研究给出的职业百分位排名归并为四个等级。它不是就业或工资预测，不是采用概率，也不区分自动化与增强。
Task-level exposure
Values in this tab are predicted labels, not observations. Eloundou et al. (2023) published two rating regimes — human raters and GPT-4 — and the β shown here is derived from the GPT-4 rater basis alone; the same task can take a different value under the other regime.
| Task | βE1 + 0.5 × E2 |
|---|---|
Reline or repair ladles and pouring spouts with refractory clay, using trowels.O*NET Task ID 13819 | 0.0 |
Chip slag from linings of ladles or remove linings when beyond repair, using hammers and chisels.O*NET Task ID 13820 | 0.0 |
Mix specified amounts of sand, clay, mortar powder, and water to form refractory clay or mortar, using shovels or mixing machines.O*NET Task ID 13821 | 0.0 |
Measure furnace walls to determine dimensions and cut required number of sheets from plastic block, using saws.O*NET Task ID 13822 | 0.0 |
Tighten locknuts holding refractory stopper assemblies together, spread mortar on jackets to seal sleeve joints, and dry mortar in ovens.O*NET Task ID 13823 | 0.0 |
Dry and bake new linings by placing inverted linings over burners, building fires in ladles, or by using blowtorches.O*NET Task ID 13824 | 0.0 |
Remove worn or damaged plastic block refractory linings of furnaces, using hand tools.O*NET Task ID 13825 | 0.0 |
Fasten stopper heads to rods with metal pins to assemble refractory stoppers used to plug pouring nozzles of steel ladles.O*NET Task ID 13826 | 0.0 |
Climb scaffolding, carrying hoses, and spray surfaces of cupolas with refractory mixtures, using spray equipment.O*NET Task ID 13827 | 0.0 |
Drill holes in furnace walls, bolt overlapping layers of plastic to walls, and hammer surfaces to compress layers into solid sheets.O*NET Task ID 13828 | 0.0 |
Spread mortar on stopper heads and rods, using trowels, and slide brick sleeves over rods to form refractory jackets.O*NET Task ID 13829 | 0.0 |
Dump and tamp clay in molds, using tamping tools.O*NET Task ID 13830 | 0.0 |
Disassemble molds, and cut, chip, and smooth clay structures such as floaters, drawbars, and L-blocks.O*NET Task ID 13831 | 0.0 |
Transfer clay structures to curing ovens, melting tanks, and drawing kilns, using forklifts.O*NET Task ID 13832 | 0.0 |
Install preformed metal scaffolding in interiors of cupolas, using hand tools.O*NET Task ID 13833 | 0.0 |
Install clay structures in melting tanks and drawing kilns to control the flow and temperature of molten glass, using hoists and hand tools.O*NET Task ID 13834 | 0.0 |
β = E1 + 0.5 × E2 · E1 = tasks where direct LLM access alone cuts time by at least 50%, E2 = tasks where software built on top of an LLM cuts time by at least 50%. Values take only 0 / 0.5 / 1.0.
Data sources & licenses — O*NET®, Eloundou et al. (2023): see full notices on the Credits page