عمال تركيب السجاد

البناء والصيانة والإصلاح

التعرّض للذكاء الاصطناعي

  • مصدر البيانات: BLSتاريخ النشر: 2026-08

    منخفض· نسبي

    منخفضأربع فئات نسبيةمرتفع جدًا

    قيمة على مستوى المجموعة المهنية

    المقياس والأساس والمصدر

    أربع فئات نسبية (منخفض / متوسط / مرتفع / مرتفع جدًا)

    831 مهنة تفصيلية في جدول توقعات التوظيف لدى BLS. وتُسند القيمة على مستوى رمز مصفوفة التوظيف الوطنية (NEM)، فالمهن التي تشترك في الرمز نفسه تأخذ النطاق نفسه

    مجموعة البيانات المصدر (تنزيل ملف XLSX)

  • مصدر البيانات: Anthropicتاريخ النشر: 2026-03

    0.000

    0.000نطاق القيم المعروضة هنا0.745
    المقياس والأساس والمصدر

    مؤشر التعرّض المرصود، 0–1 كما نُشر

    مربوط بمهام O*NET

    مجموعة البيانات المصدر

  • مصدر البيانات: ILOتاريخ النشر: 2025

    0.10

    0.09نطاق القيم المعروضة هنا0.70

    قيمة على مستوى المجموعة المهنية

    المقياس والأساس والمصدر

    مؤشر التعرّض للذكاء الاصطناعي التوليدي، 0–1 كما نُشر

    وحدة التصنيف ISCO-08 — تأخذ كل المهن ذات الرمز نفسه هذه القيمة

    محسوب من قِبل هذا الموقع وليس منشورًا من منظمة العمل الدولية: من بين 1,012 مهنة يربطها هذا الموقع بمجموعة بيانات المنظمة، تبلغ نسبة التي تساوي هذه القيمة أو تتجاوزها 98%.

    مجموعة البيانات المصدر

ما نوع القيمة التي ينشرها هذا المصدر

فئة BLS رتبة نسبية لا مستوى مطلق، وليست قياسًا مباشرًا: فهي تجمع الرتب المئينية للمهنة في عدة دراسات منشورة في أربع فئات. وهي ليست توقّعًا للتوظيف أو الأجور، ولا احتمالًا للتبني، ولا تفرّق بين الأتمتة والتعزيز.

Task-level exposure

TaskClaude.aiRaw / share %
Draw building diagrams and record dimensions.

47-2041

0.00000.0
Not observed on any surface — 15 task(s) — These tasks have no row in the source for this release. The 0 in the share row is a display-stage composition ratio; absence is what the — in the raw row states.
Join edges of carpet and seam edges where necessary, by sewing or by using tape with glue and heated carpet iron.
—0
Cut and trim carpet to fit along wall edges, openings, and projections, finishing the edges with a wall trimmer.
—0
Inspect the surface to be covered to determine its condition, and correct any imperfections that might show through carpet or cause carpet to wear unevenly.
—0
Roll out, measure, mark, and cut carpeting to size with a carpet knife, following floor sketches and allowing extra carpet for final fitting.
—0
Plan the layout of the carpet, allowing for expected traffic patterns and placing seams for best appearance and longest wear.
—0
Stretch carpet to align with walls and ensure a smooth surface, and press carpet in place over tack strips or use staples, tape, tacks or glue to hold carpet in place.
—0
Take measurements and study floor sketches to calculate the area to be carpeted and the amount of material needed.
—0
Cut carpet padding to size and install padding, following prescribed method.
—0
Install carpet on some floors using adhesive, following prescribed method.
—0
Nail tack strips around area to be carpeted or use old strips to attach edges of new carpet.
—0
Fasten metal treads across door openings or where carpet meets flooring to hold carpet in place.
—0
Measure, cut and install tackless strips along the baseboard or wall.
—0
Move furniture from area to be carpeted and remove old carpet and padding.
—0
Cut and bind material.
—0
Clean up before and after installation, including vacuuming carpet and discarding remnant pieces.
—0

Data sources & licenses — O*NET®, Anthropic Economic Index, Eloundou et al. (2023): see full notices on the Credits page

معلومات مهنية